Industrial doors in Bolszewo

BEDITOM industrial doors in Bolszewo — ranges and profiles

We operate two product lines: BEDITOM. ST40 are steel sections — a solution for industrial halls, car workshops, warehouses and outbuildings, where the rigidity of the cladding and resistance to day-to-day wear and tear are key. ALUDOOR is an aluminium structure with glazing, more commonly chosen where the door forms part of the street-facing façade or where the interior needs to be well-lit — for example, in showrooms and car washes.

We manufacture gates in sizes up to 8000 × 6000 mm, which covers virtually every opening found in commercial buildings around Wejherowo. There are five guide systems available — STL, LHR, VL, HL-INC and HLo — selected to suit the lintel, room depth and roof structure. Every door bears the CE mark and features a full range of safety features compliant with EN standards.

Free quotes for industrial doors in Bolszewo

We do not publish price lists or price ranges, as, in the case of industrial doors, two openings with the same clear width may require completely different solutions. The scope of the quotation depends primarily on:

• the dimensions of the opening and how much lintel and space there is at the sides,
• the selected guidance system — STL, LHR, VL, HL-INC or HLo,
• range and package — steel ST40 or glazed ALUDOOR, with or without a motor,
• colour and finish of the cladding and glazing,
• installation method — whether a new opening is being created, or whether we are removing an old gate or door,
• access and loading conditions — vehicle access, ground surface conditions, working height.

That is why we start with an on-site survey in Bolszewo. The survey and quote are free of charge and non-binding — after the visit, you’ll receive a specific quote for your hole, rather than a rough estimate from the internet.

Replacement and installation of gates in workshop and outbuilding complexes in Bolszewo

Bolszewo is unique because it combines two worlds: older rural buildings with farm buildings and brick garages, and new estates of detached houses built over the last decade, flanked by small industrial units and workshops on the outskirts. In older properties, we most often replace wooden swing gates or worn-out up-and-over doors — in such cases, it is necessary to check the condition of the door jambs, lintels and floor levels, as these can become warped over the years.

In newer buildings, the opening is usually standard-sized, but a low lintel or conflicting wiring beneath the ceiling can sometimes pose a constraint — the choice of routing depends on this. The town is situated inland, about 18 kilometres from the sea, so we opt for standard finishes without the need for higher protection classes. We plan the narrow residential roads in advance so that a vehicle with a gate can drive right up to the opening.

What is the process for installing industrial gates in Bolszewo?

The order process is always the same:

• Measurements — we travel to the site; it’s about 6 kilometres from Kochanów in the municipality of Luzino, so we usually arrange a date quickly. We measure the opening, the lintel and the depth of the room, and check that there is sufficient access for installation.
• Quotation and order — following a site survey, we provide a quotation for a specific door: the ST40 or ALUDOOR range, the guide system, colour and specification package. Once approved, the door goes into production.
• Installation — we remove the old gate or door, if necessary, position the guides, assemble the gate panel, and fit the operator and safety devices.
• Handover — we adjust the springs and limit switches, check that the safety devices are working correctly, demonstrate how to operate the equipment and provide the documentation, including the CE declaration.

A short journey also means that, should any adjustments or servicing be required, we can return without undue delay.

We also serve the surrounding area

Bolszewo is situated in the centre of the area we cover on a daily basis, so we combine our measurement and installation work into routes covering the whole of Wejherowo municipality and neighbouring areas. We regularly work in Gościcino, two kilometres away, and in Wejherowo itself — a four-kilometre drive. Also nearby are Kębłowo and Luzino, six and eight kilometres away respectively, whilst Strzebielino and Reda are a little further afield, at ten and eleven kilometres.

In practice, this means that if you have a workshop, warehouse or utility building anywhere within the Wejherowo district, travelling to your premises to measure industrial doors does not require us to make a special trip. Give us a call or send us an email — we’ll arrange a date for a free measurement and prepare a quote for your opening.